SERIES – C12 – FLAT TOP
Eurobelt C12 Series Flat Top reduces the polyhedron effect thanks to its 12 mm pitch and it can turn on shafts of 18 mm.
Its surface completely flat avoids the product fall. Driven by an appropriate sprocket it can reach very high conveying speeds.
- รายละเอียด
- Additional information
- บทวิจารณ์ (0)
รายละเอียด
• Pitch = 12 mm
• Open area = 0%
• Thickness = 10 mm
• Rod diameter =Ø 4.6 mm
Additional information
| น้ำหนัก | 23 kg |
|---|---|
| ขนาด | 12 x 24 x 35 cm |
มาเป็นคนแรกที่วิจารณ์ “SERIES – C12 – FLAT TOP”
สินค้าที่เกี่ยวข้อง
-
SERIES – E30 – FLUSH GRID
• Pitch = 30 mm
• Open area = 41%
• Thickness = 9 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – C12 – FLUSH GRID
Eurobelt Series C12 Flush Grid conveyor belt is ideal for product transfers at high speed in small rotation diameters. Its design with the rods in view, together with its extraordinary open surface, provides a great ease for cleaning.
-
SERIES – A24 – RAISED RIB
• Pitch = 24 mm
• Open area = 30%
• Thickness = 17 mm
• Rod diameter = Ø 4.6 mm
-
E20 – FLIGHTS AND SIDE GUARDS
STRAIGHT FLIGHT [STREAMLINE + NO CLING]
Height (h):
25 mm
50 mm
SIDE GUARDS
The side guards are plastic accessories to be inserted into the belt structure to retain the product laterally, avoiding overflows and frictions with the conveyor structure itself.
Height (h):
50 mm
-
SERIES – E30 – RAISED RIB
• Pitch = 30 mm
• Open area = 41%
• Thickness = 15 mm
• Rod diameter = Ø 4.6 mm
-
A24 – FINGER PLATES
-
SERIES – E30 – OPEN GRID
• Pitch = 30 mm
• Open area = 41%
• Thickness = 9 mm
• Rod diameter = Ø 4.6 mm
-
E93 – SPROCKETS
We also have sprockets to be used with motor drum in applications needing a special cleaning or in conveyors in which it is not possible to place the motor in the outside due to problems of space or safety.
To calculate the necessary minimum quantity of sprockets for the drive shaft as well as for the idle one, the next formula has been used:
This quantity must always be odd.
-
SERIES – E20 – TRIAN FRICTION
• Pitch = 20 mm
• Surface = Non-skid
• Thickness = 10 mm
• Rod diameter = Ø 4.6 mm
-
E20 – FINGER PLATES
They have been designed to be used with the Raised Rib belt in applications of intersection of lines in which it is necessary to transfer the product by means of finger plates.
The finger plates are manufactured in nylon and acetal. They have 13 teeth that hide among the projecting ribs of the belt, allowing the constant flow of product as the belt is engaged. They avoid the use of conventional dead plates and consequently the problems by stumbling and fall of the product.
They have two fastening holes that enable little displacements to achieve a better coupling with the belt.
Those holes are located so that they reduce to the minimum the vibrations owing to the turn of the belt over the sprockets.The finger plates can be easily installed in the structure of the conveyor putting a screw in each hole. The dimensions of these screws are: M 6 x 19 mm.
รีวิว
ยังไม่มีบทวิจารณ์