E80 – FLIGHTS AND SIDE GUARDS
The flights are plastic accessories to be inserted across the belt. They are used to push the product in ascent, descent or accompaniment applications, avoiding that it slips along the belt.
The side guards are plastic accessories to be inserted into the belt structure to retain the product laterally, avoiding overflows and frictions with the conveyor structure itself.
It is possible to cut down the standard height for special applications.
Materials: Polypropylene – Polyethylene – Polyacetal
- รายละเอียด
- Additional information
- บทวิจารณ์ (0)
รายละเอียด
STRAIGHT FLIGHT [STREAMLINE + NO CLING]
Height (h):
25 mm
50 mm
75 mm
100 mm
150 mm
BENT FLIGHT
Height (h):
70 mm
90 mm
140 mm
SCOOP FLIGHT
Height (h):
150 mm
SIDE GUARDS
Height (h):
50 mm
75 mm
100 mm
Additional information
| น้ำหนัก | 23 kg |
|---|---|
| ขนาด | 12 x 24 x 35 cm |
มาเป็นคนแรกที่วิจารณ์ “E80 – FLIGHTS AND SIDE GUARDS”
สินค้าที่เกี่ยวข้อง
-
A24 – FLIGHTS AND SIDE GUARDS
STRAIGHT FLIGHT [STREAMLINE + NO CLING]
Height (h):
25 mm
50 mm
SIDE GUARDS
The side guards are plastic accessories to be inserted into the belt structure to retain the product laterally, avoiding overflows and frictions with the conveyor structure itself.
Height (h):
50 mm
-
SERIES – E20 – TRIAN
• Pitch = 20 mm
• Surface = Non-stick
• Thickness = 10 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – E30 – TRIAN FRICTION
• Pitch = 30 mm
• Surface = Non-skid
• Thickness = 10 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – C12 – FLAT TOP
Eurobelt C12 Series Flat Top reduces the polyhedron effect thanks to its 12 mm pitch and it can turn on shafts of 18 mm.
Its surface completely flat avoids the product fall. Driven by an appropriate sprocket it can reach very high conveying speeds.
-
E20 – FLIGHTS AND SIDE GUARDS
STRAIGHT FLIGHT [STREAMLINE + NO CLING]
Height (h):
25 mm
50 mm
SIDE GUARDS
The side guards are plastic accessories to be inserted into the belt structure to retain the product laterally, avoiding overflows and frictions with the conveyor structure itself.
Height (h):
50 mm
-
E20 – FINGER PLATES
They have been designed to be used with the Raised Rib belt in applications of intersection of lines in which it is necessary to transfer the product by means of finger plates.
The finger plates are manufactured in nylon and acetal. They have 13 teeth that hide among the projecting ribs of the belt, allowing the constant flow of product as the belt is engaged. They avoid the use of conventional dead plates and consequently the problems by stumbling and fall of the product.
They have two fastening holes that enable little displacements to achieve a better coupling with the belt.
Those holes are located so that they reduce to the minimum the vibrations owing to the turn of the belt over the sprockets.The finger plates can be easily installed in the structure of the conveyor putting a screw in each hole. The dimensions of these screws are: M 6 x 19 mm.
-
SERIES – E20 – FLUSH GRID
• Pitch = 20 mm
• Open area = 32%
• Thickness = 9 mm
• Rod diameter = Ø 4.6 mm
-
E30 – FINGER PLATES
-
SERIES – E20 – FLAT TOP
• Pitch = 20 mm
• Open area = 0%
• Thickness = 10 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – A24 – RAISED RIB
• Pitch = 24 mm
• Open area = 30%
• Thickness = 17 mm
• Rod diameter = Ø 4.6 mm
รีวิว
ยังไม่มีบทวิจารณ์