E41 – RAISED RIB
Eurobelt Series E41 Raised Rib conveyor belt, given its configuration of projecting ribs, enables us to make product transfers by using finger plates.
The central reinforcement of the ribs allows the lateral entrance of cans, glass jars, or containers in general, avoiding their overturning as well as any damag
- รายละเอียด
- Additional information
- บทวิจารณ์ (0)
รายละเอียด
• Pitch = 40 mm
• Open area = 25%
• Thickness = 22 mm
• Rod diameter = Ø 6 mm
Additional information
| น้ำหนัก | 23 kg |
|---|---|
| ขนาด | 12 x 24 x 35 cm |
มาเป็นคนแรกที่วิจารณ์ “E41 – RAISED RIB”
สินค้าที่เกี่ยวข้อง
-
SERIES – E30 – OPEN GRID
• Pitch = 30 mm
• Open area = 41%
• Thickness = 9 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – E20 – FLAT TOP
• Pitch = 20 mm
• Open area = 0%
• Thickness = 10 mm
• Rod diameter = Ø 4.6 mm
-
E20 – FLIGHTS AND SIDE GUARDS
STRAIGHT FLIGHT [STREAMLINE + NO CLING]
Height (h):
25 mm
50 mm
SIDE GUARDS
The side guards are plastic accessories to be inserted into the belt structure to retain the product laterally, avoiding overflows and frictions with the conveyor structure itself.
Height (h):
50 mm
-
SERIES – E20 – RAISED RIB
• Pitch = 20 mm
• Open area = 32%
• Thickness = 15 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – E30 – PERFORATED
• Pitch = 30 mm
• Open area = 17%
• Thickness = 10 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – E30 – FLUSH GRID
• Pitch = 30 mm
• Open area = 41%
• Thickness = 9 mm
• Rod diameter = Ø 4.6 mm
-
E20 – FINGER PLATES
They have been designed to be used with the Raised Rib belt in applications of intersection of lines in which it is necessary to transfer the product by means of finger plates.
The finger plates are manufactured in nylon and acetal. They have 13 teeth that hide among the projecting ribs of the belt, allowing the constant flow of product as the belt is engaged. They avoid the use of conventional dead plates and consequently the problems by stumbling and fall of the product.
They have two fastening holes that enable little displacements to achieve a better coupling with the belt.
Those holes are located so that they reduce to the minimum the vibrations owing to the turn of the belt over the sprockets.The finger plates can be easily installed in the structure of the conveyor putting a screw in each hole. The dimensions of these screws are: M 6 x 19 mm.
-
SERIES – E30 – TRIAN FRICTION
• Pitch = 30 mm
• Surface = Non-skid
• Thickness = 10 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – E20 – FLUSH GRID
• Pitch = 20 mm
• Open area = 32%
• Thickness = 9 mm
• Rod diameter = Ø 4.6 mm
-
A24 – FLIGHTS AND SIDE GUARDS
STRAIGHT FLIGHT [STREAMLINE + NO CLING]
Height (h):
25 mm
50 mm
SIDE GUARDS
The side guards are plastic accessories to be inserted into the belt structure to retain the product laterally, avoiding overflows and frictions with the conveyor structure itself.
Height (h):
50 mm
รีวิว
ยังไม่มีบทวิจารณ์