-
E40 – SPROCKETS
-
E41 – FINGER PLATES
They have been designed to be used with the Raised Rib belts in applications in which it is necessary to transfer the product by means finger plates.
The finger plates are manufactured in nylon and acetal. They have 15 teeth that hide among the projecting ribs of the belt, allowing the constant flow of product as the belt is engaged. They avoid the use of conventional dead plates and consequently the problems by stumbling and fall of the product.
They have three fastening holes that enable little displacements to achieve a better coupling with the belt. Those holes are located so that they reduce to the minimum the vibrations owing to the turn of the belt over the sprockets.
The finger plates can be easily installed in the structure of the conveyor putting a screw in each hole. The dimensions of these screws are: M 6 x 19 mm.
-
E41 – RAISED RIB
Eurobelt Series E41 Raised Rib conveyor belt, given its configuration of projecting ribs, enables us to make product transfers by using finger plates.
The central reinforcement of the ribs allows the lateral entrance of cans, glass jars, or containers in general, avoiding their overturning as well as any damag -
E41 – SPROCKETS
-
E50 – CONIC
Eurobelt Series E50 Conic has a smooth surface with small pyramidal-shaped elevations that provide a greater coefficient of friction, as well as they avoid the slippery products to change their position during the conveyance.
-
E50 – FLAT TOP
Eurobelt Series E50 Flat Top, due to its closed surface, completely flat and smooth, avoids any damage and overturn in the product, as well as the resulting line blockage.
It is the conveyor belt most commonly used in elevating conveyors for products in bulk, and in delicate product conveyance. -
E50 – FLIGHTS AND SIDE GUARDS
The flights are plastic accessories to be inserted across the belt. They are used to push the product in ascent, descent or accompaniment applications, avoiding that it slips along the belt.
The side guards are plastic accessories to be inserted into the belt structure to retain the product laterally, avoiding overflows and frictions with the conveyor structure itself.
It is possible to cut down the standard height for special applications.
Materials: Polypropylene – Polyethylene
-
E50 – FLUSH GRID
Eurobelt Series E50 Flush Grid has a grille-shaped configuration, with a 40% open area, and a completely smooth surface.
It is ideal for applications in which there are a lot of debris of the conveyed product, as their removal is very easy by means of air or water under pressure.
It is specially recommended for cooling and freezing tunnels. -
E50 – KNURLED
Eurobelt Series E50 Knurled has a flat-corrugated surface that has been designed to prevent the conveyed product from adhering to the belt. Due to its corrugated surface, it is used in slightly inclined conveyors as well.
-
E50 – OPEN GRID
Eurobelt Series E50 Open Grid, with a grille-shaped configuration, and a 40% open area, is suitable for applications in which drainage through the belt is required.
We have accomplished an exclusive design of this conveyor belt consisting of two transverse projections in the middle of every pitch to achieve the product do not adhere to the belt.. -
E50 – PERFORATED
Eurobelt Series E50 Perforated Flat Top has an 18% open area, a completely smooth surface, and grille-shaped small straight holes without structural obstacles, to make easy the drainage of any liquid.
The dimensions of these holes, in millimetres, are:
[1.8 x 6], [2 x 9] and [2 x 15]. -
E50 – SLIDING ROLLERS
Eurobelt Series E50 Sliding Rollers is provided with small rollers inserted on its surface that rotate around themselves whenever there is product accumulation, avoiding crushing and wear in the base of the product.
This conveyor belt has been designed mainly to solve problems of conveyance of boxes, containers, etc.
WELCOME TO BKPPASS CO.,LTD.|
0-2918-2977-78 |CONTACT US
© Copyright 2011-2024. All Rights Reserved.