A24 – FLIGHTS AND SIDE GUARDS
STRAIGHT FLIGHT [STREAMLINE + NO CLING]
Height (h):
25 mm
50 mm
SIDE GUARDS
The side guards are plastic accessories to be inserted into the belt structure to retain the product laterally, avoiding overflows and frictions with the conveyor structure itself.
Height (h):
50 mm
- รายละเอียด
- Additional information
- บทวิจารณ์ (0)
รายละเอียด
The flights are plastic accessories to be inserted across the belt. They are used to push the product in ascent, descent or accompaniment applications, avoiding that it slips along the belt.
• Its non-stick side has ribs that project over the surface to prevent the product from sticking.
• Their edges are completely rounded to avoid any damage of the product.
It is possible to cut down the standard height for special applications.
Materials: Polypropylene – Polyethylene – Polyacetal
Additional information
| น้ำหนัก | 23 kg |
|---|---|
| ขนาด | 12 x 24 x 35 cm |
มาเป็นคนแรกที่วิจารณ์ “A24 – FLIGHTS AND SIDE GUARDS”
สินค้าที่เกี่ยวข้อง
-
SERIES – E20 – RAISED RIB
• Pitch = 20 mm
• Open area = 32%
• Thickness = 15 mm
• Rod diameter = Ø 4.6 mm
-
E20 – FINGER PLATES
They have been designed to be used with the Raised Rib belt in applications of intersection of lines in which it is necessary to transfer the product by means of finger plates.
The finger plates are manufactured in nylon and acetal. They have 13 teeth that hide among the projecting ribs of the belt, allowing the constant flow of product as the belt is engaged. They avoid the use of conventional dead plates and consequently the problems by stumbling and fall of the product.
They have two fastening holes that enable little displacements to achieve a better coupling with the belt.
Those holes are located so that they reduce to the minimum the vibrations owing to the turn of the belt over the sprockets.The finger plates can be easily installed in the structure of the conveyor putting a screw in each hole. The dimensions of these screws are: M 6 x 19 mm.
-
SERIES – E30 – OPEN GRID
• Pitch = 30 mm
• Open area = 41%
• Thickness = 9 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – E30 – FLAT TOP
• Pitch = 30 mm
• Open area = 0%
• Thickness = 10 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – E20 – TRIAN
• Pitch = 20 mm
• Surface = Non-stick
• Thickness = 10 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – E30 – TRIAN FRICTION
• Pitch = 30 mm
• Surface = Non-skid
• Thickness = 10 mm
• Rod diameter = Ø 4.6 mm
-
E93 – SPROCKETS
We also have sprockets to be used with motor drum in applications needing a special cleaning or in conveyors in which it is not possible to place the motor in the outside due to problems of space or safety.
To calculate the necessary minimum quantity of sprockets for the drive shaft as well as for the idle one, the next formula has been used:
This quantity must always be odd.
-
SERIES – E20 – FLAT TOP
• Pitch = 20 mm
• Open area = 0%
• Thickness = 10 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – E30 – PERFORATED
• Pitch = 30 mm
• Open area = 17%
• Thickness = 10 mm
• Rod diameter = Ø 4.6 mm
-
SERIES – A24 – FLUSH GRID
• Pitch = 24 mm
• Open area = 30%
• Thickness = 11 mm
• Rod diameter = Ø 4.6 mm
รีวิว
ยังไม่มีบทวิจารณ์